Effect of Soil Stabilization on Structural Design of Flexible Pavement

Main Article Content

Shalaw Abdullah Saleh
Rahel Shwana Ismael
Binar Salman Abas

Abstract

Inadequate subgrade conditions often diminish the lifespan of pavements built on these soils. However, this challenge can be addressed through various methods, including soil stabilization, which enhances soil strength. This research focuses on soil stabilization using two types of waste materials (rubber and plastic) as additives in concentrations of 5%, 10%, and 15%, along with a consistent cement inclusion of 3% across all samples. Different tests, such as Sieve analysis, Atterberg Limits, Specific Gravity, Standard proctor Test and California Bearing Ratio, were performed for both the soil and the additive materials. As a result, this stabilization approach improved the California Bearing Ratio (CBR), leading to thinner pavement layers, which potentially lowers construction costs. Notably, the highest CBR observed was 49.95% with 10% plastic, while the top result for rubber was a 28.01% CBR at 5% inclusion. These enhancements in CBR values contributed to reducing the total thickness of the pavement layers by (435 mm) for both materials.

Article Details

How to Cite
Saleh, S. A., Ismael, R. S. ., & Abas, B. S. . (2024). Effect of Soil Stabilization on Structural Design of Flexible Pavement. Journal of Studies in Civil Engineering, 1(1), 36–54. https://doi.org/10.53898/jsce2024113
Section
Original Articles

References

Roy, A. (2014). Soil stabilization using rice husk ash and cement. International journal of civil engineering re-search, 5(1), 49-54.

Mishra, S., Sachdeva, S. N., & Manocha, R. (2019). Subgrade soil stabilization using stone dust and coarse aggregate: A cost-effective approach. International Journal of Geosynthetics and Ground Engineering, 5(3), 1-11.

Afrin, H. (2017). A review on different types of soil stabilization techniques. International Journal of Transporta-tion Engineering and Technology, 3(2), 19-24.

Abdul-Rahman, F., & Wright, S. E. (2014). Reduce, reuse, recycle: alternatives for waste management.

Kalliyath, J., Joy, J., Paul, J., & Vadakkel, A. M. (2016). Soil stabilization using plastic fibers. International Journal of Science Technology & Engineering, 2(12), 484-487.

Dahale, P. P., Nagarnaik, P. B., & Gajbhiye, A. R. (2012). Utilization of solid waste for soil stabilization: a re-view. Electronic Journal of Geotechnical Engineering, 17(Bund Q).

Katte, V. Y., Mfoyet, S. M., Manefouet, B., Wouatong, A. S. L., & Bezeng, L. A. (2019). Correlation of California bearing ratio (CBR) value with soil properties of road subgrade soil. Geotechnical and Geological Engineering, 37(1), 217-234.

Abdullah Saleh, S., & Jalal Khoshnaw, G. (2020). Effect of Soil Stabilization on Subgrade Soil Using Cement, Lime, and Fly Ash. Eurasian Journal of Science & Engineering, 6(2), 39-52.

Paria, S., & Yuet, P. K. (2006). Solidification–stabilization of organic and inorganic contaminants using portland cement: a literature review. Environmental reviews, 14(4), 217-255.

Adeyanju, E. A., & Okeke, C. A. (2019, November). Clay soil stabilization using cement kiln dust. In IOP Confer-ence Series: Materials Science and Engineering (Vol. 640, No. 1, p. 012080). IOP Publishing.

James, J., & Pandian, P. K. (2016). Industrial wastes as auxiliary additives to cement/lime stabilization of soils. Advances in Civil Engineering, 2016.

Das, B. M. (2003). Chemical and mechanical stabilization. Transportation Research Board.

Balkis, A., & Macid, S. (2019). Effect of cement amount on CBR values of different soil. Avrupa Bilim ve Teknoloji Dergisi, (16), 809-815.

Mallikarjuna, V., & Mani, T. B. (2016). Soil stabilization using plastic waste. International Journal of Research in Engineering and Technology, 5(5), 391-394.

Hambirao, G. S., & Rakaraddi, P. G. (2014). Soil stabilization using waste shredded rubber tire chips. IOSR Journal of Mechanical and Civil Engineering, 11(1), 20-27.

ASTM D6913-04(2009) e1. Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis

ASTM D854-23. Standard Test Methods for Specific Gravity of Soil Solids by the Water Displacement Method

ASTM D4318-17e1. Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils

ASTM D698-12(2021). Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft3 (600 kN-m/m3))

ASTM D1883-21. Standard Test Method for California Bearing Ratio (CBR) of Laboratory-Compacted Soils

AASHTO Guide for design of pavement structures, 1993